Replace the screw pump. Keep the Throughput.
Extreme Rotary Valves meter material into your conveying line and seal against differential pressure the same dual job your screw pump does, without the wear-prone screw flight, the shop rebuilds, or the power bill.

+40%
energy reduction vs. comparable screw pump systems
550+ BHN
through-hardened P-33 rotor and wear shoe
35 PSIG
differential pressure on the new HPXL valve
800°F
continuous duty on high-temp models
2026 ACA Manufacturer's Award Winner
Since 1921 · Performance. Durability. Innovation.
Dense phase in partnership with Clyde Pneumatic Conveying
Extreme platform since 1964 · 6″–24″ sizes
Why Plants Are Rethinking the Screw Pump
Escalating Maintenance Costs
Rebuild frequency and part costs continue to climb as materials get harder to handle.
Accelerating Wear Rates
Increasingly aggressive, abrasive feed materials shorten service intervals.
Long Lead Times
Custom repair parts and inferior aftermarket components stretch downtime.
Dilute Phase Conversion
Up to 50-65 TPH

A reliable, cost-effective transition using high-velocity, lower-pressure conveying extreme-duty components neutralize the added wear from higher velocity. ​
Mid-Pressure Upgrade
Keeps Motive Air Source Drop-in, flange-to-flange options

Keeps the plant's current operating philosophy while upgrading to a medium-pressure, medium-velocity system — lower energy draw, reduced wear, technologically advanced drop-in replacement for existing screw pump piping.
Dense Phase Conversion
Long distance / high tonnage

Low velocity, high pressure — material moves in concentrated slugs. Delivered via partnership with Clyde Pneumatic Conveying (Denseveyor®, D-Pump®, MD-Pump®) for the most severe-duty, abrasive applications.
Delta Ducon Solutions Offer +40% Energy Reduction
It's not just screw pumps causing feed problems

"So-called" heavy-duty rotary valves
Fabricated rotors sealing directly against the housing. High wear, inefficient maintenance, limited pressure and temperature ratings treated like a commodity, not an engineered solution.

Double dump valves
Good at high temperature, but they cycle hard to imitate continuous flow. Flaps and seals wear fast and replacement parts are expensive.
Maintenance + downtime = lost revenue.
Scope of application
Materials we're feeding today
Every material below runs through Extreme Rotary Valves in active cement, lime and minerals service.
Cement
Fine, abrasive finished product to silo and load-out
Limestone
Coarse to fine raw feed; highly abrasive crushed rock
CKD / LKD
Fine, abrasive finished product to silo and load-out
Coal & petroleum coke
Erosive primary and alternative kiln fuel feed
Fly ash
Fine pozzolan for blended cement and SCM production
Harvested / beneficiated ash
Coarser, hotter reclaimed pond ash for spec-grade SCM
Other SCMs
Slag cement, natural pozzolans and emerging alternative binders
Have a tougher material?
Send us your material data →
1
STANDARD
Packing + Air Purge

-
Packing: (3) rope-type, Teflon-impregnated graphite rings
-
Lantern ring: brass or PTFE
-
Air purge: connection on end plate; kit includes filter/regulator, flow meter, bracket, hose & fittings
Standard seal arrangement
2
Cartridge Style Seal
ALTERNATE

-
Replaces packing and lantern ring inside the stuffing box
-
Face seal perpendicular to shaft: no abrasive shaft wear Materials: silicone (food grade, std) or EPDM; 304 SS rotors; PTFE 3000 stator
-
Air: 15 PSIG clean, dry air
Rated to 500°F max
3
ALTERNATE
Air Mizer Air Seal

-
Non-contacting seal: no wear-prone contact surfaces
-
Positive air purge keeps product in the valve with minimal air use Best for fine abrasives at high differential pressure
-
Replaces the entire stuffing box assembly
Rated to 500°F max Standard
Higher Temp Models Available
The legacy workhorse, under pressure
Why plants are rethinking the screw pump
For decades the screw pump was the backbone of dry bulk transport in cement and minerals. It is 100-year-old technology that has largely gone unchanged, and today's materials, power prices and uptime targets are exposing it.

01
Escalating maintenance cost
Rebuild frequency and part costs keep climbing as materials get harder to handle.
02
Accelerating wear rates
Rebuild frequency and part costs keep climbing as materials get harder to handle.
03
Escalating maintenance cost
Rebuild frequency and part costs keep climbing as materials get harder to handle.
04
Escalating maintenance cost
Rebuild frequency and part costs keep climbing as materials get harder to handle.
05
Escalating maintenance cost
Rebuild frequency and part costs keep climbing as materials get harder to handle.
A design proven since 1964
The PERMA/flo Extreme Rotary Valve is both a volumetric feeder and a high-differential airlock. It meters material into the conveying line while sealing against line pressure the role your screw pump plays today, without the rotating screw flight that wears out.
One valve. Two jobs.

Type XT redesign — rotor pockets go from 9 to 10, and the inlet throat grows up to 82% on 6″–12″ models to cut bridging
2003
Type XL introduced — the original Extreme Rotary Valve platform
1964
2004
Enhanced sealing arrangements and wear-resistant feature set
Today
6″–24″ sizes serving cement, mining, power and steel, plus the new HPXL High Pressure Extreme Rotary Valve
The core differentiator: metallurgy
Cast solid. Not surface-hardened.
The rotor and wear shoe are solid castings of P-33, a proprietary chrome-nickel-iron alloy. Hardness runs through the whole part, so the valve keeps its integrity long after surface wear begins.
-
Standard valves use cast iron, carbon or stainless steel — soft next to silica- and alumina-bearing materials like fly ash, cement and limestone.
-
Surface coatings and tiled ceramic wear through and expose the softer base metal underneath.
-
P-33 is through-hardened: the same abrasion resistance at the surface and at the core.

Brinell hardness (40–60 Rc)
550+
3x
harder than standard stainless steel

